ticketslasas.blogg.se - Swissknife windows 10 premium

#SWISSKNIFE WINDOWS 10 PREMIUM HOW TO#
#SWISSKNIFE WINDOWS 10 PREMIUM CODE#
#SWISSKNIFE WINDOWS 10 PREMIUM DOWNLOAD#

Via CAD Forum – How to re-format the Autodesk instalation USB key? This procedure may lead to a damage of your USB key and is completely unsupported. Then click Start.īe warned! Make sure you have a backup copy of your original installation files. Start the downloaded EXE and click “Reset Write Protect”, W.P select Un-Write Protect. This tool can be downloaded here (file MI_ReFixInfo_1_0_0_1.7z). To overwrite this USB key you can use the utility SMI ReFixInfo.

Autodesk Product Design Suite Ultimate 2013 uses the USB key of the type “DaneElec zMate Aero” (blue) – see Dane-Elec – with the controller SM3254Q AE. If you want to “misuse” this USB memory to store your data you can “hack” it with internal reformatting, make it a standard R/W device.Į.g. The installation USB flash memory (key, dongle) used for distribution of Autodesk Design Suites is a read-only device and cannot be overwritten or formatted with standard methods. I used smi_mptool_v2.03.34_v7_j1118_3254ae and now it works.Īfter few minutes the device is ready to use.ĮDIT 6 – for Autodesk Product Design Suite Ultimate 2013 Inside my USB Drive (also named DaneElec zMate USB 32 GB) I found a controller SM3254Q AE, produced by SMI. Format the drive using the Windows format tool (or other tool of your choice) as NTFS.ĮDIT – 5 From the comments, for DaneElec zMate USB 32 GB: Unplug your USB drive and plug it back in.ĥ.

#SWISSKNIFE WINDOWS 10 PREMIUM DOWNLOAD#

Download the file from this link… and extract it to your drive.ģ. I found a solution for the latest drive that I received with the PS2251-67 Controller.ġ. Set Controller to PS2251-62 and FC1-FC2 to 01ĮDIT 7 – For PS2251-67 (From Ryan Ruta in the Comments) Run getinfo in MPALL_F1_9000_v363_0C folder

#SWISSKNIFE WINDOWS 10 PREMIUM CODE#

In Firmware tick ‘Do ISP’ ‘Erase Code Block’ and ‘Auto ISP’ Set Controller to PS2251-67 and FC1-FC2 to 01 Recieved Brand New USB’s For Autodesk Design Suite 2013 Premiumĭownload MPALL_F1_9000_v363_00 and MPALL_F1_9000_v363_0C You can try this process in MPALL (step 1 above): Run MPALL 363 c (as per settings below) (make sure its revision C).This may seem a bit long winded, but I think it might be a good way for 2013 media kit: YOU MUST USE USB3Ĭopy the contents between the = to a new file named 2014_2251-03.iniĬlick Setting, select “Advanced Setting” then press OKĬlick the load button and select the 2014_2251-03.ini file you created earlier.

He also provides a link to download the proper version, at:

Do not try to force a certain BIN file onto the drives firmware using MPALL.

Do not use the formatter.zip on the latest 2014 version TOSHIBA USB 3.0 with the 2251-03.

Click start, the process lasts for about a minute and it’s doneWARNINGSThere is some evidence of newer drives being bricked.

Close settings window by clicking on “x”.

Choose advance settings and load the ini file, the same that Mike created.

Start it, put your usb stick into your USB 3.0 port.